Why does the exhaust pipe fail when the water well drilling rig is started?

Diagnosis of a rig that can turn over when starting, but does not start (no smoke in the exhaust). When starting the engine, no smoke is discharged from the exhaust pipe and there is no outburst sound, which generally belongs to the problem of the oil circuit and is analyzed in detail as follows:

① There is no oil in the fuel tank.

② fuel filter, oil and water separator clogging.

③ Low-pressure oil circuit does not supply oil.

④ The injector pump does not pump oil.

⑤ Air in the fuel line.

⑥ The gas distribution phase is out of alignment. The opening moment of the valve is not coordinated with the stroke of the piston in the cylinder. If the piston in the cylinder for the compression stroke, the inlet and exhaust valves are open, fresh air is driven out of the cylinder, so that there is no combustion gas in the cylinder, can not start.

⑦ The solenoid valve of the type injection pump is bad and in a closed state, and the diesel fuel cannot enter the high-pressure chamber.

If you don't know how to choose the right water well drilling rig, click the link below to contact our professional team directly.

Comments

How to extend the life of drill pipe

1. When using a new drill pipe, the drilling rig manufacturer should make sure that the wire fasteners on the front cut-off (protecting the shaft head) of the drill bit are also close to the new one. A ring-buckled rotating head can easily damage the wire fasteners of the new drill pipe, resulting in leaks, snaps, and loosening, and so on. 2. In the use of drill pipe for a drilling, should be first “grinding new buckle”, which consists of, first smeared with silk buckle oil, and then use the drill rig full torque, and then open the buckle, and then smeared with silk buckle oil and then open, and so on for three times, you can avoid the new wear and buckle. 3. As far as possible to maintain the drill pipe under the ground and on the ground in a straight line, so as to avoid part of the side of the wire buckle force and cause unwanted wear and tear, or even jump buckle, pay attention to the rig anchored to avoid the construction of the force to move is very important. 4. The buckle...

What are the Basic Maintenance Methods for Water Well Drilling Rigs

Cleaning: After every day's operation, clean the mud, oil, and other debris on the rig in time to keep the rig clean. Checking lubrication: regularly check the lubrication points to ensure that the lubricant is sufficient and the grease is clean. Fasteners check: you can check whether the bolts and nuts of each part are loose and tighten them in time. Hydraulic system checks: you can check whether the hydraulic oil level is normal, whether there is no leakage phenomenon, and whether the hydraulic oil is clean. Lubrication system maintenance: regular replacement of lubricating oil, grease, cleaning oil filter, and oil tank. Hydraulic system maintenance: regular replacement of hydraulic oil, cleaning hydraulic filter. Cooling system maintenance: clean the radiator, and check the coolant level. Transmission system maintenance: check the tightness of the transmission belt, and replace the worn transmission belt. Electrical system maintenance: check whether the line is firm...

Use and maintenance of drill bits

Use and maintenance of drill bits: 1. Choose a suitable drill bit: Before using a drill bit, it is necessary to select the appropriate type and specification of drill bit based on drilling conditions and needs. 2. Installing the drill bit: When installing the drill bit, it is necessary to ensure that the connection between the drill bit and the drill pipe is firm, and to correctly install the cutting teeth of the drill bit. 3. Maintain appropriate drilling speed and pressure during the drilling process: Excessive drilling speed and pressure can lead to premature wear and damage of the drill bit, while too small can affect drilling efficiency. 4. Regular inspection and maintenance: Regularly check the wear of the drill bit and replace severely worn components in a timely manner. At the same time, it is necessary to regularly clean and lubricate the drill bit to extend its service life. 5. Storage and preservation: When storing and preserving drill bits, it i...

Pearldrill Drilling Rig And Drill bits

Search This Blog