Skip to main content

Why does the waer well drilling rig's engine crankshaft not turn?

 A crankshaft that fails to turn when the rig is started is a mechanical failure.

Repair engine start, in the starting system is intact, press the starting switch, the starter motor has a ringing sound and the crankshaft can not rotate, also belongs to the mechanical failure.
① Poor meshing of the starter and flywheel teeth. The tooth ring and the starter gear will collide when starting the engine, resulting in damage to the teeth or wear on one side of the teeth. If more than three consecutive teeth are damaged or badly worn, the starter gear and ring teeth will be difficult to mesh.
② Sticky cylinders. Engine temperature is too high when the engine stops and stalls, the heat is difficult to dissipate, and the high temperature of the piston ring and cylinder adhesion, after cooling, can not start.
③ Crankshaft locking. Due to the lubrication system failure or lack of oil caused by the sliding bearing dry friction, so that ultimately hold the crankshaft and can not start.

④ Injector pump plunger stuck.

water well drilling rig

If you don't know how to choose the right water well drilling rig, click the link below to contact our professional team directly.

Contact us

Comments

Post a Comment

Popular posts from this blog

How to extend the life of drill pipe

  1. When using a new drill pipe, the drilling rig manufacturer should make sure that the wire fasteners on the front cut-off (protecting the shaft head) of the drill bit are also close to the new one. A ring-buckled rotating head can easily damage the wire fasteners of the new drill pipe, resulting in leaks, snaps, and loosening, and so on. 2. In the use of drill pipe for a drilling, should be first “grinding new buckle”, which consists of, first smeared with silk buckle oil, and then use the drill rig full torque, and then open the buckle, and then smeared with silk buckle oil and then open, and so on for three times, you can avoid the new wear and buckle. 3. As far as possible to maintain the drill pipe under the ground and on the ground in a straight line, so as to avoid part of the side of the wire buckle force and cause unwanted wear and tear, or even jump buckle, pay attention to the rig anchored to avoid the construction of the force to move is very important. 4. The buckle...
Post a Comment
Read more

What are the Basic Maintenance Methods for Water Well Drilling Rigs

  Cleaning: After every day's operation, clean the mud, oil, and other debris on the rig in time to keep the rig clean. Checking lubrication: regularly check  the lubrication points to ensure that the lubricant is sufficient and the grease is clean. Fasteners check: you can check whether the bolts and nuts of each part are loose and tighten them in time. Hydraulic system checks: you can check whether the hydraulic oil level is normal, whether there is no leakage phenomenon, and whether the hydraulic oil is clean. Lubrication system maintenance: regular replacement of lubricating oil, grease, cleaning oil filter, and oil tank. Hydraulic system maintenance: regular replacement of hydraulic oil, cleaning hydraulic filter. Cooling system maintenance: clean the radiator, and check the coolant level. Transmission system maintenance: check the tightness of the transmission belt, and replace the worn transmission belt. Electrical system maintenance: check whether the line is firm...
Post a Comment
Read more

Use and maintenance of drill bits

Use and maintenance of drill bits: 1. Choose a suitable drill bit:  Before using a drill bit, it is necessary to select the appropriate type and specification of drill bit based on drilling conditions and needs. 2. Installing the drill bit:  When installing the drill bit, it is necessary to ensure that the connection between the drill bit and the drill pipe is firm, and to correctly install the cutting teeth of the drill bit. 3. Maintain appropriate drilling speed and pressure during the drilling process:  Excessive drilling speed and pressure can lead to premature wear and damage of the drill bit, while too small can affect drilling efficiency. 4. Regular inspection and maintenance:  Regularly check the wear of the drill bit and replace severely worn components in a timely manner. At the same time, it is necessary to regularly clean and lubricate the drill bit to extend its service life. 5. Storage and preservation:  When storing and preserving drill bits, it i...
Read more