What is seasonal maintenance for water well drilling rigs

Acording to the climate characteristics of different seasons, the water well drilling rig to take targeted maintenance measures, can effectively improve the performance of the equipment and extend the life.

1. Spring Maintenance
Cleaning and inspection:
Remove soil, oil, and frost left over from winter, and check for rusted parts.
Lubrication maintenance:
Refill lubricant for each transmission part to prevent insufficient lubrication due to the influence of low temperatures in winter.
Hydraulic system inspection:
Check the hydraulic oil level and piping for leakage or aging due to cold weather.

2. Summer Maintenance
Cooling system maintenance:
Check whether the mud cooling system and diesel engine coolant are normal to prevent the equipment from overheating due to high temperatures.
Lubricating oil check:
Under high-temperature environments, pay attention to checking the viscosity of lubricating oil and replacing it with high-temperature resistant oil in time.
Dust maintenance:
The operating environment is dusty in summer. To prevent clogging, regularly clean the air filter, mud pump, and other key parts.

3. Fall Maintenance
Equipment cleaning:
After operation, thoroughly clean the drilling rig mud, rock chips and dust to prevent dirt accumulation.
Rust prevention treatment:
Apply anti-rust oil to rust-prone parts (e.g., drill pipe joints and bolts) in the alternating fall and winter to prevent rust caused by moisture.
System Inspection:
Test hydraulic oil, diesel fuel and circuit system in advance to prepare for winter operation.

4. Winter Maintenance
Antifreeze measures:
Replace the antifreeze to ensure the cooling system does not freeze.
Empty the water in the mud pipe after operation to prevent freezing and blockage.
Diesel engine maintenance:
Use low-temperature starting device or preheating equipment to ensure smooth low-temperature diesel engine starting.
Lubrication Protection:
Use low-temperature lubricating oil to reduce the impact of the cold environment on the transmission system.
Storage Management:
When out of service for a long time, store the equipment indoors or cover it with a protective cover to avoid erosion by wind and snow.

Summarize
Spring focuses on cleaning and restoration; summer prevents heat and dust;
Fall focuses on cleaning and rust prevention; winter focuses on frost prevention and low-temperature protection.

Adjust the maintenance program flexibly according to seasonal characteristics to ensure efficient operation and prolong the service life of the equipment.

If you don't know how to choose the right water well drilling rig, click the link below to contact our professional team directly.

Contact us

Comments

How to extend the life of drill pipe

1. When using a new drill pipe, the drilling rig manufacturer should make sure that the wire fasteners on the front cut-off (protecting the shaft head) of the drill bit are also close to the new one. A ring-buckled rotating head can easily damage the wire fasteners of the new drill pipe, resulting in leaks, snaps, and loosening, and so on. 2. In the use of drill pipe for a drilling, should be first “grinding new buckle”, which consists of, first smeared with silk buckle oil, and then use the drill rig full torque, and then open the buckle, and then smeared with silk buckle oil and then open, and so on for three times, you can avoid the new wear and buckle. 3. As far as possible to maintain the drill pipe under the ground and on the ground in a straight line, so as to avoid part of the side of the wire buckle force and cause unwanted wear and tear, or even jump buckle, pay attention to the rig anchored to avoid the construction of the force to move is very important. 4. The buckle...

What are the Basic Maintenance Methods for Water Well Drilling Rigs

Cleaning: After every day's operation, clean the mud, oil, and other debris on the rig in time to keep the rig clean. Checking lubrication: regularly check the lubrication points to ensure that the lubricant is sufficient and the grease is clean. Fasteners check: you can check whether the bolts and nuts of each part are loose and tighten them in time. Hydraulic system checks: you can check whether the hydraulic oil level is normal, whether there is no leakage phenomenon, and whether the hydraulic oil is clean. Lubrication system maintenance: regular replacement of lubricating oil, grease, cleaning oil filter, and oil tank. Hydraulic system maintenance: regular replacement of hydraulic oil, cleaning hydraulic filter. Cooling system maintenance: clean the radiator, and check the coolant level. Transmission system maintenance: check the tightness of the transmission belt, and replace the worn transmission belt. Electrical system maintenance: check whether the line is firm...

Use and maintenance of drill bits

Use and maintenance of drill bits: 1. Choose a suitable drill bit: Before using a drill bit, it is necessary to select the appropriate type and specification of drill bit based on drilling conditions and needs. 2. Installing the drill bit: When installing the drill bit, it is necessary to ensure that the connection between the drill bit and the drill pipe is firm, and to correctly install the cutting teeth of the drill bit. 3. Maintain appropriate drilling speed and pressure during the drilling process: Excessive drilling speed and pressure can lead to premature wear and damage of the drill bit, while too small can affect drilling efficiency. 4. Regular inspection and maintenance: Regularly check the wear of the drill bit and replace severely worn components in a timely manner. At the same time, it is necessary to regularly clean and lubricate the drill bit to extend its service life. 5. Storage and preservation: When storing and preserving drill bits, it i...

Pearldrill Drilling Rig And Drill bits

Search This Blog